FUNKE TPL PDF

Construction. FUNKE brazed plate heat exchangers are made of cor- rugated stainless steel plates. The plates are assembled in a ° angle to each other. FUNKE brazed plate heat exchangers series TPL is basically made of non- corrugated stainless steel plates. In the flow gaps special stainless steel turbulence. User instructions. These instructions relate to the standard versions of the brazed FUNKE plate heat exchanger (PWT). Supplementary operating and.

Other standard product types such as shell and tubes and air blast oil coolers are held in semi stock and are assembled to individual requirements and despatched within working days.

TPL satisfy the high demands in this area with funek to reliability and thermodynamic efficiency — and can be tp with the utmost flexibly! During assembly every second unit is rotated degrees to form two separate flow tunke that act as turbulators ensuring a highly turbulent flow which enables the most effective heat transfer and reduces the risk of fouling to a minimum.

Originally developed specifically for applications such as cooling hydraulic and motor oil, TPL brazed plate heat exchangers are also ideally suited and deployable for other application processes in mechanical tp, plant engineering.

Pure counter flow is employed to achieve maximum possible heat transfer. The heat-exchanging surface of these units is between 0. Air Blast Heat Exchangers. Normally consisting of two halves, fastened to the Heat exchanger with straps or tensions bolts. A leak indication hole in the gasket signals leakage to atmosphere.

Another advantage of the TPL is its high resilience, as the surface soldering makes it possible to achieve a significantly higher level of safety under stress compared to the spot soldering used in conventional brazed plate heat exchangers.

The major advantage of bolted type heat exchanger is its ability to expand or reduce surface area according to varying heat load conditions. The turbulence plates are available in different versions, making the technical design very flexible.

Be the first to review! Two pressure plates clamp this package together with tie rods.

Download enquiry form for Plate Heat Exchanger. Small sizes with low space requirements are possible for media with funje viscosity thanks to the high heat transfer of the powerful TPL. Each individual flow channel can be adapted to the specific application thanks to the modular design of the TPL.

Funke Wärmeaustauscher Apparatebau GmbH

Product Details The exceptionally high heat transfer performance is achieved by means of diagonal media flow as well as special turbulence plates inserted into the flow gaps, a technology developed and produced exclusively by FUNKE.

Funkr types of plate heat exchangers do not use gaskets and undergo a strict quality inspection programme, including pressure and leak-tests to ensure absolute leak tightness. From Plate Heat Exchangers.

The added advantage is a smaller overall sizing and lower cost due to a higher achieved ratio of heat load to mass. All plates are provided with a double gasket at inlet and outlet, which prevents mixing of media. Technical Data Heat exchange surface per plate: Limiting condition of operation: Single pass and multi-pass arrangements are standard with a surface area of up m2 in one unit.

Stress conditions in the heat exchanger caused by differences in pressure or temperature, for example, can be absorbed significantly better thanks to the surface soldering of the TPL. The BHE consists of embossed stainless steel plates, fitted into one another and vacuum brazed with copper or nickel solders to form a compact and pressure-tight unit.

For example, should a design specification dictate a too small FPS selection the problem can be rectified on site with minimal down times – simply by adding a proportionate amount of plates at marginal cost.

Product Details – Industry Mall – Siemens USA

TPL can be used universally with different media. Port connections can be supplied to client requirements. The exceptionally high heat transfer performance fuke achieved by means of diagonal media flow as well as special turbulence plates inserted into the flow gaps, a technology developed and produced exclusively by FUNKE. The TPL Series utilizes additional turbulator plates in the flow gaps and increased flow gaps compared to other plate types.

GAlternative material for special tol is available on request. The TPL is particularly well suited to flow media with average to high viscosity. Material of plates St.

Frigotherm represents Funke Heat Exchangers Germany in South Africa, which permits us to supply any type of plate heat exchangers. We keep a large assortment of plates in stock and can deliver nation-wide within short periods.

OIL COOLER TPL 00-L-18-12 FUNKE

Standard connections include threaded socket or nipple, metal lining and fnke connections. Given optimal operating conditions the BHE is practically maintenance free. Each plate is provided with a gasket, which seals the flow gaps to atmosphere and the media from one another. The optional extended end plates also facilitate the installation of the already very compact units.

The plate package is mounted in a rack consisting of a fixed number of plates.