FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Nicage Akikree
Country: Germany
Language: English (Spanish)
Genre: Science
Published (Last): 26 July 2015
Pages: 232
PDF File Size: 17.21 Mb
ePub File Size: 14.64 Mb
ISBN: 808-9-86254-277-5
Downloads: 3886
Price: Free* [*Free Regsitration Required]
Uploader: Kagam

All maintenance should be carried out in accordance with established safety practices. Ground resistance must be less than ? This includes being completely familiar with all associated documentation for the said product. Whenever any of the following symbols are encountered, its associated note must be read and understood.

Terminal layouts The following selection of terminal layouts are taken from the FX1N product range. C M3 screw to secure top cover.

Mitsubishi FX1NMT-DSS Manuals

Note all counters are latched Remarks C0 to C15 Type: Remove the base unit top cover. Software warning 4 Indicates special care must be taken when using this element of software.

D Top cover for board.

DC source transistor, CE registered. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.

If during the installation of these product or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site. Please refer to the table below. When using a DC powered unit, the input circuit power supply should be used.

Parallel LED Eqn 1: Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded. It should be read and understood before attempting to install or use the unit. The definition of such a person or persons is as follows; a Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role.

  DESCARGAR LIBRO EL FUGITIVO STEPHEN KING PDF

D, D M Program execution error ref. Secure top cover with M3 screw E. Plug board A into connector B. These engineers should also be trained in the use and maintenance of the completed product.

All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams. Always ensure that mounted units and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment.

Upper hardwarr, D read from VR1. If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site.

E C A Special function or optional equipment board. Remotely from a personal computer or other programming peripheral. Screw terminals must be secured to prevent a loose connection from causing a malfunction.

The following instructions are also not suitable. Manuap that fd1n ground cable must not be connected to the same ground as the power circuits.

Mitsubishi FX1N-24MT-ESS/UL Manuals

To release, pull the spring loaded clips away from the rail and slide the unit up and off. A standard input X0 to X17 defined by the system parameters. If the current leakage is greater than the stated value, then add Rb.

  GINGIVOESTOMATITIS HERPETICA PDF

E M3 screw to secure top cover. If a response time of 0. The manual has been written to be used by trained and competent personnel.

Once installation is complete remove the protective paper band, to prevent overheating. Verify the program to ensure it has been written to the PLC correctly. See equation 1 for Rb calculation. Check the output LEDs for operation.

PL E xtension block? Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment. If resistance Rp is less than the stated value, then add Rb.

FX1N Hardware Manual_图文_百度文库

Always make sure the power is turned off, before installing a special function board. The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA. See equation 2 for Rb calculation. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

If a high speed response is required, a current of 10 – mA must be used. Hardwsre mount them to the floor or ceiling of an enclosure. Input circuit power supply?