IEC 61375 PDF

The train communication network (TCN) is a hierarchical combination of two fieldbus for data transmission within trains. It consists of the Multifunction Vehicle Bus (MVB) inside each vehicle and of the Wire Train Bus (WTB) to connect the different vehicles. The TCN components have been standardized in IEC IEC and UIC have now been issued as a set of international standards to overcome this situation: IEC , the Train Communication Network. STANDARD. IEC. First edition. Electric railway equipment –. Train bus –. Part 1: Train Communication Network. Matériel électrique ferroviaire .

Author: Guzuru Daisho
Country: Czech Republic
Language: English (Spanish)
Genre: Career
Published (Last): 23 February 2004
Pages: 157
PDF File Size: 11.8 Mb
ePub File Size: 12.3 Mb
ISBN: 228-7-87720-273-4
Downloads: 57028
Price: Free* [*Free Regsitration Required]
Uploader: Kagahn

Still all the alternate vehicle buses are connected to the Wire Train Bus. MVB for critical operation such as traction control and signalling in the driver’s cab, and LON for uncritical and slow data transfer, but low-cost connections such as passenger displays and diagnostics.

Interfaces are listed by their speed in the roughly ascending order, so the interface at the end of each section should be the fastest. Additionally more and more 613375 are added to rail vehicles that need far more bandwidth than any field bus can provide e. A unique property of ice WTB is the train inauguration Zugtaufe in which the newly connected vehicles receive an address in sequence and can identify the vehicle side called port and starboard like in the marine so that doors open on the correct side.

Vehicles without WTB node “conduction vehicles” are not counted. This is not due to the communication technology: But railways certification is costly and not always needed for uncritical applications such as comfort and passenger information.

Train communication network – Wikipedia

This page was last edited on 9 Augustat This explains why MVB and FIP have similar operation cyclic and event-drivenonly the arbitration method in case of multiple access differs, as MVB used a binary bisection mode relying of collision detection while FIP piggy-backed a “look-at-me” bit over periodic data. Up to 32 addresses can be dynamically allocated. The MVB standard was introduced to replace the multitude of field buses in the train equipment. From Wikipedia, the free encyclopedia.

  DAVID ELKIND HURRIED CHILD PDF

Rail technologies Serial buses Automation. Technical and de facto standards for wired computer buses.

The frames have a 661375 payload of bits. MVB is similar to FlexRayboth have the “process data”, which is called “static segment” in FlexRayand “message data”, which is the “dynamic segment” and are driven by a fixed TDMA scheme.

The medium consists of a duplicated shielded twisted pair cable, which runs in the UIC cables between the vehicles. The difference came from the fieldbus physical layer which assumes a phase-locked loop to decode the Manchester data, requiring a preamble to synthonize the decoder, while MVB operated principally with optical fibres where this method is useless, MVB’s decoding relies on zero-crossing detectors and Manchester pattern recognition.

The multifunction vehicle bus connects individual nodes within a vehicle or in a closed train set.

Retrieved from ” https: The plugs and sockets are the same as used by Profibus with two 9-pin Sub-D sockets per electrical device. The physical level is using transmissions at a 1. The WTB operates cyclically to provide deterministic operation, with a period of 25 ms, used mainly for the traction control. Despite the similarities, no rail-manufacturer has considered FlexRay, since they valuated a common solution higher than a multitude of ief busses.

Train communication network

This separation uec not always observed. This was intentional as the fight between the field busses raged in the s and the decision of the IEC that any of the eight field busses was a standard did not help plug-compatibility. There is no inauguration, the addresses are statically allocated. The train communication network TCN is a hierarchical combination of two fieldbus for data 6135 within trains.

  CALCULO MULTIVARIABLE STEWART 6 EDICION PDF

The wire train bus has been designed for international passenger trains with variable composition, consisting of up to 22 vehicles. By using this site, you agree to the Terms of Use and Privacy Policy.

IEC | IEC Webstore

Running FlexRay with 2. The MVB frames are not compatible with IEC fieldbus frames as it omits most of the preamble 613375 which is not required if zero-crossing detection is possible.

When two train compositions join, the addresses are reallocated to 61357 a new composition of vehicles with a sequential address. Since connectors are exposed and can oxidize, a current pulse is applied at connection establishment to evaporate the oxide layer, called fritting.

The maximum distance is determined on the restriction of a maximum allowed reply delay of The connector between the vehicles is the pole UIC connector. While the WorldFIP, CANopen, Lonworks and Profinet are controlled by international manufacturer associations targeting a wide range of application, MVB was tailored to the rolling stock application, with the goal of plug-compatibility, and therefore allows no 6175.

Webarchive template archiveis links CS1 German-language sources de. The content of the periodic and sporadic frames is governed by the UIC standard.

Views Read Edit View history. Archived from the original powerpoint on The WTB also supports sporadic data transmission for diagnostics. No repeaters are foreseen since vehicles in between can have discharged batteries.

When total cost of ownership is considered, the cost of the hardware elements can easily be outweighed by additional engineering costs in the railways market with its small series.