INVERSOR YASKAWA V7 PDF
1. PREFACE. Omron Yaskawa Motion Control (from now OYMC) V7AZ is a small and simple Inverter, as easy to use as a contactor. This instruction manual. Yaskawa’s Varispeed V7 is a small and simple Inverter; as easy to use as a inspection, troubleshooting, and specifications of the Varispeed V7. Read. YASKAWA is not responsible for any modification of the product made by the user, doing .. To mount the VS V7, dimensions as shown below are required.
|Published (Last):||8 January 2018|
|PDF File Size:||8.29 Mb|
|ePub File Size:||12.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Maximum Output Fre- n Run Commands from invrsor and the frequency reference are effective when the multi-function input terminal for this setting is closed register No. Frequency Detection 6 Programming Features Set n, n or n to 4. Back to home page.
OMRON VARISPEED V7 User Manual
Learn More – opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc. Page Do not set.
When an inconsistency in the settings is found,: Enabled invegsor when n is set to 1 pulse monitor output. If sending a Run Com- mand while changing a constant, such as during a test run, yaskaaw sure to observe all safety precautions. For V Class Inverters, the voltage values n, n, and n should be doubled. The Inverter will stop the motor for approximately 1 minute yaskasa then set the required motor constants automatically while operating the motor for approximately 1 minute. Carrier Frequency Set the carrier frequency selection n to 5 kHz or more n Motor 2 Maximum Out- Characteristics The wire sheath strip length must be 5.
Be sure to remove the top and bottom covers when Inverter 5P5 or 7P5 of open chassis mounting type is used.
See other items More Image not available Photos not available for this variation.
No stall prevention when a brak- ing resistor is installed Note: Read this tatives or the nearest Yaskawa sales office inveesor provide the manual number shown on the front cover. Yaskawa J Instrukcja Uruchomienia. Carry out the self-test in the following procedure. Function Indicators Set constants required for autotuning.
Page 4 Confirm that all indicators are OFF before proceeding. Page If constant n is ysskawa to 3 standard motor, motor 1 only or 4 special motor, motor 1 onlyhowever, OL1 calculations for motor 1 will always be performed, regardless of the status of the Motor Switching Command. Confirm that all indicators are OFF before proceeding.
Yaskawa CIMR-V7AA45P5 Inverter VS mini V7 (free shipping) | eBay
See terms – opens in a new window or tab. Torque Detection 6 Yqskawa Features Torque Detection If an excessive load is applied to the machine, an increase in the output current can be detected to output an alarm signal to multi-function out- put terminal MA, MB, P1, or P2.
The following flowchart describes each function indicator. V Class 3-phase to kW. Operator circuit terminal current reference CN The indicators are lit, unlit or flashing reflecting the order of priority. Details of Indicators Color in parenthesis indicates the color of the indicator. After wiring is complete, be sure to make the following settings before operation.
Page Fre- quency Reference Upper Limit n No additional import charges at delivery!
Depends on Inverter capacity. Remove the top and bottom covers so that Inverters of 5. If both the target value and the feedback values are zero, adjust n so that the Inverter yasskawa frequency is zero.
Follow the warnings when handling the Inverter. Yasakwa text from picture: This item will be shipped yaskwwa the Global Shipping Program and includes international tracking. Output Frequency n Note: To halt the Inverter by a fault at undertorque detection, set to 2 or 4.
Line-to-neutral Resistanceand n Motor No-load Current accord- ing to the motor test report. To connect a reactor between the Inverter and the motor, set n to the sum of the initial value of n Motor Leakage Inductance and the externally mounted reactor inductance.
If any part of V7AZ is missing or damaged, call for service immediately. The output current or out- Flashing put torque was less than the detection level n or n A checksum error occurred in the constant Initialize the constants.
The constant data cannot be changed when this constant is set. Set the input terminal for a multi-step speed reference using the multi- function input selection. Page of Go. By pressing ‘print’ button you will print only current page.
Control wiring must be less than 50 invrrsor ft in length and must be separated from power wiring.